Page 1 of 3

Never Anything Easy Nor Simple

Posted: Fri Jun 16, 2023 9:34 pm
by 19&41
My Explorer Limited put up a check engine light. I found, with my code reader that the driver's upstream o2 sensor was affected. I got a new one and had my great nephew replace it. He had some trouble getting the connector to seat and lock but he got it together. I started the engine and the CEL had dissapeared. However, when I drove the car it came back. The code reader showed all the o2 sensors were either failed or pending failure. I decided the only way forward was to take it to the dealership palace and have them diagnose it. That was yesterday. I called them today to check on it. the service advisor said "I have good news and bad news" She said "The tech had just finished the diagnosis. The bad news is that the problem in with the PCM. That is a part that Ford has obsoleted and is no longer available." As an added bonus, they are not available at the major auto parts stores (through Cardone Mfg.)

Re: Never Anything Easy Nor Simple

Posted: Fri Jun 16, 2023 10:17 pm
by electra225
Wonder if anyone rebuilds them?

Re: Never Anything Easy Nor Simple

Posted: Fri Jun 16, 2023 10:28 pm
by TC Chris
Click and Clack were big advocates of the black-tape method.

Me, when my Ranger recently flashed its light, I took it in for diagnosis. The shop reset the device, showing an O2 sensor issue. It stayed off for them. I drove away. It came back on. I made a nice little piece of cardboard to keep the light out of my eyes until I could get back into the shop. Black tape seemed too sticky. I reached for my cardboard and started the truck again. The light was off and stayed off. So maybe just threatening to ignore the light will make it go away.

Chris Campbell

Re: Never Anything Easy Nor Simple

Posted: Sat Jun 17, 2023 12:30 am
by William
My 1994 Ford Ranger's check engine light comes on all the time. When read, it says there is a problem with the power steering. OK, the fluid is full and the PS is steering the truck. The code has been cleared several times but eventually it will come back on, then off, then on, then off. I now choose to ignore it.

Bill

Re: Never Anything Easy Nor Simple

Posted: Sat Jun 17, 2023 1:27 am
by electra225
I found this outfit, courtesy of "Mr. Bing". I know nothing about them, but they say they sell Ford PCM's. I hope this helps, at least gives you a place to start. ;) ;)

https://www.fs1inc.com/ford-pcm-ecm-ecu ... 0(Rebuilt)

Re: Never Anything Easy Nor Simple

Posted: Sat Jun 17, 2023 2:22 am
by 19&41
I'm looking into a repair place. Thanks Greg, but The modules they have are a bit pricy. I also have to work out getting to work while the module is sent out.

Re: Never Anything Easy Nor Simple

Posted: Sat Jun 17, 2023 1:56 pm
by 19&41
Here is a vendor I'm considering. https://www.ebay.com/itm/374197620984?f ... R9zV6pmZYg

The dealer run down also states that the car fails emissions inspection, so ignoring the CEL is not an option.

Re: Never Anything Easy Nor Simple

Posted: Sun Jun 18, 2023 4:56 pm
by hermitcrab
Give it the Shango066 treatment... he repaired those ford PCM's on his site a few times... didn't look that bad...

Re: Never Anything Easy Nor Simple

Posted: Sun Jun 18, 2023 7:06 pm
by William
I found a few repair suggestions on YouTube on how to repair the ABS module on a GM the S and T line. I thought, what the heck and I tried it. Worked like a charm and saved me between $500.00 -$1000.00.

Bill

Re: Never Anything Easy Nor Simple

Posted: Mon Jun 19, 2023 3:29 am
by TC Chris
William wrote: ↑Sun Jun 18, 2023 7:06 pm I found a few repair suggestions on YouTube on how to repair the ABS module on a GM the S and T line.
OK, I'll bite. What's the "S and T line"???

Chris Campbell

Re: Never Anything Easy Nor Simple

Posted: Mon Jun 19, 2023 11:11 am
by William
The "S" stands for 2-wheel drive, and the "T" stands for 4-wheel drive and pertains to the Chevy/GMC line of small trucks. S10 p/u, GMC Jimmy, those GM vehicles.

Bill

Re: Never Anything Easy Nor Simple

Posted: Mon Jun 19, 2023 12:53 pm
by 19&41
I work on circuits of this detail at my job, but only with a set of manuals detailing the function of each portion of the circuit. I have nothing more than a block diagram of the PCM in my literature on the unit. One mistake and my car goes from my primary vehicle to something that is able to roll onto a flatbed to go to the scrapyard. If there is a place that repairs them with a known good track record, I'd rather take a chance with that.

Re: Never Anything Easy Nor Simple

Posted: Mon Jun 19, 2023 3:25 pm
by Firedome
Early obsoleting of electronics makes vehicles of the '90s onward more difficult to keep running than those from around 1980 and earlier.

Re: Never Anything Easy Nor Simple

Posted: Mon Jun 19, 2023 3:30 pm
by 19&41
I'll wager there will be aftermarket suppliers rising to meet this need soon. They can handle the overhead on supplying this vital component.

Re: Never Anything Easy Nor Simple

Posted: Tue Jun 20, 2023 12:59 am
by William
Good luck, Rex and I hope it turns out to be an easy and affordable repair.

Bill

Re: Never Anything Easy Nor Simple

Posted: Tue Jun 20, 2023 1:24 am
by electra225
I wager that auto manufacturers are obsoleting vital parts for internal combustion engine-powered vehicles so owners will be forced into buying an electric vehicle...... ;) :roll:

I have a friend who recently had the engine replaced in a 2002 Chevy pickup, a 4.8 Liter V-8. Just the rebuilt long block cost him almost $7000 from the dealer. I used to buy complete new 350's and 366's from this dealer for $1800 including a 50,000 mile warranty. The truck is still in nice shape. Lest you wonder why somebody would spend that kind of money on a 20 year old truck....... ;) ;)

A new one similar to it would be almost 80 grand! Plus, the old one is paid for. ;) ;) :D :D

Re: Never Anything Easy Nor Simple

Posted: Tue Jun 20, 2023 2:38 am
by 19&41
Thanks, Bill. We'll see.

Re: Never Anything Easy Nor Simple

Posted: Tue Jun 20, 2023 4:43 am
by TC Chris
electra225 wrote: ↑Tue Jun 20, 2023 1:24 am
A new one similar to it would be almost 80 grand! Plus, the old one is paid for. ;) ;) :D :D
I cannot imagine paying $80K for a device to drive around, surrounded by drunk drivers, people chattering on cell phones, road-ragers, and the occasional kamikaze deer. The most I've ever paid for a vehicle was the $10K for my sweet Ranger.

Chris Campbell

Re: Never Anything Easy Nor Simple

Posted: Tue Jun 20, 2023 11:22 am
by 19&41
For $80K it should be a house, not rolling stock.

Re: Never Anything Easy Nor Simple

Posted: Tue Jun 20, 2023 11:29 am
by William
I totally agree, Rex.

Bill