Phonola 1057

Discussions about instruments in smaller cabinets. If they don't set on the floor, they belong here. Tube and solid state, stereo and mono.
Post Reply
User avatar
Hi-Fi-Mogul
Anchor Member
Posts: 1365
Joined: Sat Jul 10, 2021 1:53 am
Contact:

Phonola 1057

Post: # 30958Post Hi-Fi-Mogul »

Started the re-cap on this three tube 1958 Waters-Conley player.

Someone had put in a 47 mF cap for the 80 mF filter.
They put in a 10 mF cap for the 20 mF cathode bypass cap.

And they left all the old wax/paper caps so I would not
be bored !

They left the B- wire from the old capacitor can connected in circuit.

I'll finish up by installing the new correct 82 mF, and
new 22 mF filter caps.

This gal has 3 speakers in the cabinet, so I hope the
sound is good.

I've already serviced the V-M changer.

(BTW, the Sams has several wiring and notation errors,
if anyone may spot them)


.
Attachments
Phonola 1057 Chassis Internal-A.JPG
Phonola Chassis Internal-1.png
Phonola Sams.png
Hi-Fi-Mogul
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: Phonola 1057

Post: # 30960Post electra225 »

Sams gets a bad rap for making mistakes. My thinking is that, on record player amps especially, that manufacturers used the same basic amp for many different models. They would move components to accomodate the different arrangements in cabinets. That record player should sound pretty good. What cartridge does it use?
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
Hi-Fi-Mogul
Anchor Member
Posts: 1365
Joined: Sat Jul 10, 2021 1:53 am
Contact:

Re: Phonola 1057

Post: # 30962Post Hi-Fi-Mogul »

electra225 wrote: ↑Tue Nov 03, 2026 2:01 am That record player should sound pretty good. What cartridge does it use?
Greg,

There is a Sonotone 2-T in the tonearm.

IIRC, it is functional.

As you stated, these 50C5, 12AV6, 35W4 amps were ubiquitous,
and my next phono is a Zenith AP9-B with a very similar
50C5, 12AV6, 35W4 chassis.
Hi-Fi-Mogul
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: Phonola 1057

Post: # 30963Post electra225 »

The Sonotone 2-T is a nice, warm sounding cartridge. I'm assuming some version of the VM 1200 series, right?
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
TC Chris
Anchor Member
Posts: 3779
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: Phonola 1057

Post: # 30965Post TC Chris »

That's not a standard low-end amp. Look at the interesting bass control, using a separate tap on the output transformer. The treble control is a standard high-cut design running high off to ground. It's always cool when somebody gets creative.

I will be interested in reports on how it sounds.

Chris Campbell
User avatar
Hi-Fi-Mogul
Anchor Member
Posts: 1365
Joined: Sat Jul 10, 2021 1:53 am
Contact:

Re: Phonola 1057

Post: # 31092Post Hi-Fi-Mogul »

Finished up this gal, she sounds very nice.

When I had it all back in the cabinet, the
"tweeter" had a bad buzz.

Removing the speaker revealed that a not so small piece
of the baffle board was broken and sitting next to
the cone.

A wonder the cone was not damaged.

The tweeter's felt voice coil cover was off, and I
noticed 2 small wood screws on the magnet.

So, all the "extra" parts were removed, and the
tweeter is fine.

The bass response is VERY good, but I wonder why
there is no resistor or capacitor there for a filter
for the two smaller speakers vs the woofer.

Now on to the Zenith.

.
.
Attachments
Phonola 1057 Completed.png
Phonola 1057 Complete.png
Hi-Fi-Mogul
User avatar
William
Global Moderator
Posts: 5514
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: Phonola 1057

Post: # 31093Post William »

That is a nice looking unit, Mr. Mogul, nice job. Keeper or to be sold?

Bill
User avatar
TC Chris
Anchor Member
Posts: 3779
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: Phonola 1057

Post: # 31094Post TC Chris »

Hi-Fi-Mogul wrote: ↑Tue Nov 17, 2026 5:46 pm

Removing the speaker revealed that a not so small piece
of the baffle board was broken and sitting next to
the cone.

A wonder the cone was not damaged.



The bass response is VERY good, but I wonder why
there is no resistor or capacitor there for a filter
for the two smaller speakers vs the woofer.
As to the tweeter, the cones on those are usually quite stiff, so there would be little excursion and little likelihood of cone damage.. And that may be why they omitted a crossover--if the smaller speakers were stiff-coned, they have a mechanical crossover effect--the speakers just don't respond to bass frequencies.

Chris Campbell
User avatar
stbasil
Hero Member
Posts: 290
Joined: Mon Nov 04, 2024 5:29 pm
Location: Wimberley TX
Contact:

Re: Phonola 1057

Post: # 31095Post stbasil »

Beautiful job, Mogul! The design, though simple, even has negative feedback with real bass and treble controls plus multiple speakers. The designers obviously paid attention to the final sound, with good results!
Jack of all trades & Master of none in Wimberley TX
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests