speakers and misc.

The place to talk about almost anything, as long as it's nice......
Post Reply
User avatar
TC Chris
Anchor Member
Posts: 3778
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

speakers and misc.

Post: # 3020Post TC Chris »

Questions. First: What's the best source for speaker-surround replacement kits? Out in the shop is a 15" speaker my neighbor gave me quite a few years ago. I move it to get into the book case and move it again to get into the paint cabinet. The surround (foam, of course) has crapped out. Last time I re-did speakers was when I built out the shop in 1997. That company doesn't seem to be around now. I'd prefer butyl rubber, not foam. I've also got a couple Utah acoustic suspension bookshelf speakers with dead foam. Eventually these should all be repaired. Experience with companies?

Second, I've got a little Stanley remote on-off switch for a light--a clicker plus a plug-in receiver that the lamp plugs into. It only works when the clicker is right next to the receiver. Battery is OK. Both units are physically OK inside. Both have short wires inside as antennas, at some UHF frequency. Any ideas to make it work?

Chris Campbell
User avatar
William
Global Moderator
Posts: 5513
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: speakers and misc.

Post: # 3021Post William »

Chris, I have never replaced a speaker surround, but have a friend that has. I will make an inquiry to him and find out where he gets his. Stay tuned!

Your Stanley remote sounds like my garage door opener. I have two garage doors that side by side. One works great, the other you need to be right in front of the door to get it to open. Battery is good, everything seems to be the same as the good working one. I'm stumped?

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: speakers and misc.

Post: # 3028Post hermitcrab »

I have replaced the surrounds on my 1970's 12" fisher speakers , I got them from speakerworks and it was a pretty easy to do just make sure the coil is not rubbing ... the glue they supplied with the kit looked suspiciously like plain old white elmers glue ... :lol:
User avatar
macgolf
Senior Member
Posts: 128
Joined: Sat Jul 10, 2021 4:05 pm
Location: Bloomington, IL
Contact:

Re: speakers and misc.

Post: # 3035Post macgolf »

Chris,

I re-foamed several pairs of speakers as well as re-centering a few with rubber surrounds that suffered from woofer sag. Unless it's from an AR or others that requires filleted surrounds most vendors should be OK. Sorry I haven't ordered in a few years and can't remember my last vendor but it looks like others have that covered. My glue choice will always be Aleene's Tacky Glue. It's available in the craft section of many stores. Some kits came with a model kit type glue. My experience was that glue set up too quickly for centering the VC.
1960 Philco H-1916
1962 Montgomery Wards
1963 Pilot 6B500
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: speakers and misc.

Post: # 3037Post electra225 »

You might try Parts Express, Chris. They have lots of stuff. I really like their black speaker grill cloth. There are several videos on YouTube that show how to refoam speakers. Good lcuk.
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
SeniorSteve
Full Member
Posts: 61
Joined: Wed Aug 04, 2021 11:43 am
Location: St Paul, MN
Contact:

Re: speakers and misc.

Post: # 3040Post SeniorSteve »

I've used www.simplyspeakers.com and have had very good results. The glue they ship with the surrounds is more of a model car type cement, but I did like how it set up quicker then the Aileen's white glue. It really depends on the speaker you are working on, I've been successful with both types of glue. I agree, I would rather use the butyl rubber surrounds as they tend to last much longer. If you do change from foam to butyl rubber surrounds it will change the characteristics of the speaker resonance.
User avatar
William
Global Moderator
Posts: 5513
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: speakers and misc.

Post: # 3041Post William »

Chris, I checked with my friend and he gets his surrounds from Parts Express. Greg, suggested them as well. He said he likes their product and has had good luck with it. I hope this helps.

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: speakers and misc.

Post: # 3043Post hermitcrab »

I use parts express quite a bit, they are reasonable in price and they are located in central OH , so shipping is only a couple days to Mich.
User avatar
19&41
Global Moderator
Posts: 1984
Joined: Thu Jul 08, 2021 10:11 pm
Location: Jonesboro, Georgia
Contact:

Re: speakers and misc.

Post: # 3044Post 19&41 »

On your remotes, they are probably crystal controlled transmitters. If the tuning goes off in that circuit due to component degradation or whatever, it may be enough off center to not allow any contact unless it's close.
"Any sufficiently advanced technology is indistinguishable from magic."
-Arthur C. Clarke
"It is difficult to get a man to understand something when his salary depends upon his not understanding it."
-Upton Sinclair
User avatar
TC Chris
Anchor Member
Posts: 3778
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: speakers and misc.

Post: # 3054Post TC Chris »

I'll check out Parts Express--have bought speakers from them. The last time I did this (1997) the surround kits came with what looked like white glue. It has held up. Current plans seem to call for removing the dust cap to center the voice coil with shims.When I did it in '97, no such worries. They just instructed you to press the cone down and release it.

About 10 or 15 years ago my big LR speakers lost their foam surrounds all at once--speakers and passive radiators. I had just had hand surgery and couldn't do it myself so I shipped them off to a guy who used to work for the company before it went belly-up. He used butyl rubber at my request and I worried about response changes, but could not hear any.

Chris Campbell
User avatar
Motorola minion
Anchor Member
Posts: 854
Joined: Sun Jul 11, 2021 2:23 pm
Location: Central PA
Contact:

Re: speakers and misc.

Post: # 3069Post Motorola minion »

I have used a speaker rebuilder in NJ, who is easy to ship to and has done about 5 speakers for me. Mainly I had deteriorated cones on mid-30s Philco consoles, requiring more than routine compliance replacement.

My foray into speaker repair was on two pairs of vintage large bookshelf speakers; Genesis 2A and Epicure I's.

Both had foam surrounds long gone, great mylar dome tweeters and were a bargain at $5 Habitat reStore. I have the Epicures on a SABA receiver that only pushes 15 watts, the one driver "pops" rif driven too hard. So, the Genesis turned out better and are connected to a friend's Kenwood in his Deli's kitchen, a speaker that seems well matched to it.

The ADS L620 speakers with 10" drivers and rubber surrounds, bought with HS graduation money, are OK after all these years. The perf-metal grilles are claw-proof and projectile resilient, an accident of choice I never regretted, living with all kinds of pets since.
User avatar
TC Chris
Anchor Member
Posts: 3778
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: speakers and misc.

Post: # 3105Post TC Chris »

Motorola minion wrote: ↑Wed Nov 17, 2021 3:28 pm My foray into speaker repair was on two pairs of vintage large bookshelf speakers; Genesis 2A and Epicure I's.
There have been at least 3 Genesis hi-fi speaker companies. Mine, Genesis 210 models, are from Genesis Physics Corp., a long-gone company. Maybe related to yours? Seems to me that the guy who did my surrounds when my hand was disabled also did Epicures, and there may have been some relation between the companies. I chose butyl rubber so I would not have to do them over. I bought these new back in the 1980s so I have amortized the cost completely.

Chris Campbell
User avatar
macgolf
Senior Member
Posts: 128
Joined: Sat Jul 10, 2021 4:05 pm
Location: Bloomington, IL
Contact:

Re: speakers and misc.

Post: # 3168Post macgolf »

TC Chris wrote: ↑Mon Nov 15, 2021 3:25 am Current plans seem to call for removing the dust cap to center the voice coil with shims.When I did it in '97, no such worries. They just instructed you to press the cone down and release it.

Chris Campbell
I usually just play music at a low volume to keep the VC centered. I had 2 pair of British pairs that had suffered from sag, I played a 60hz tone through them to make sure there was no rub as I pressed the outsides onto the frames. Shimming with card stock is more foolproof but I haven't needed to go there yet.

Mark
1960 Philco H-1916
1962 Montgomery Wards
1963 Pilot 6B500
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: speakers and misc.

Post: # 3183Post hermitcrab »

Do they make replacement rubber surrounds?.... these foam replacements are just going to crumble again in 10 years ... maybe less with the cheapness of today's materials ...
User avatar
TC Chris
Anchor Member
Posts: 3778
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: speakers and misc.

Post: # 3201Post TC Chris »

Last time I looked various places offered your choice. My Genesis speakers had the foam (boo) replaced with butyl (yay).

Chris Campbell
Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests