New project...

Discussions of all brands of consoles not listed above, tube and solid state, stereo and mono.
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: New project...

Post: # 23248Post electra225 »

I don't see the inductors connected together. They terminate on the same board, but are not connected. What am I seeing wrong? :oops:
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
TC Chris
Anchor Member
Posts: 3779
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: New project...

Post: # 23249Post TC Chris »

electra225 wrote: ↑Fri Oct 18, 2024 4:47 am I don't see the inductors connected together. They terminate on the same board, but are not connected. What am I seeing wrong? :oops:
Look at the last photo--wires from the terminals on the strip are soldered together at the center rivet.

Chris Campbell
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: New project...

Post: # 23250Post electra225 »

I see that now. :oops: :oops:

A black wire usually means it's a "common" wire. I'm not familiar with that circuit at all..... :oops:
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23252Post hermitcrab »

Greg , that black wire was on that end when I got it... if this is interpreted as the ground side , then there are not enough connections for the speakers ....the right/left inputs were connected to the end with 4 wires which also makes no sense ... if the main audio is plugged into that end with the four wires , then it by-passes the LC network all together?... I thought the center two wires should be the input from the amp, then the LC network makes sense with the four wires ... the two outside wires the midrange and the two inside wires the tweeters , but where do the woofers connect to?.... I think I will scrap this crossover and use a couple Chinese made ones I have in the basement , because without the cabinet wiring diagram I am stumped on using the original.
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: New project...

Post: # 23254Post electra225 »

I can't see what you are working with and am having trouble painting a picture in my head of that setup. Can you identify the wires that come off the amp? Seems like there should be at least three. Left channel positive, right channel positive and perhaps at least a common negative. If you have a transistor radio with an earphone jack, those make convenient signal sources to trace speaker wiring. Make a test lead to plug into the earphone jack, then use that source to trace your speaker wires to and thru that crossover network. If that doesn't work, then your idea of making your own crossover network may be the only way to go. How could that potentially change the "personality" of the amp?
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23256Post hermitcrab »

I posed this question on the FB Vintage console forum with the pictures , and the consensus seems to be , the tied together inductors are the ground, the wires in the center are for the tweeters, the outer 2 of the 4 wire end is the woofers, the inner pair is the midrange... the input from the amp is also plugged into the outer terminals on the 4 wire end , and after looking at it for a while It seems logical to me. so I will give it a try when I get that far , still routing a ton of wires in the cabinet , they were not cheap on the wire they used, the phono wires are as thick as RG8 cable...it also has the jacks for tape in and out and remote speakers trying to imagine how the wires were originally ran without criss-crossing all over is tough.
User avatar
electra225
Site Admin
Posts: 9074
Joined: Thu Jul 08, 2021 7:48 pm
Location: San Tan Valley, AZ
Contact:

Re: New project...

Post: # 23259Post electra225 »

Magnavox stuffed the wires in every which way, then put the back on the cabinet before they all fell out..... :roll:
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
User avatar
William
Global Moderator
Posts: 5515
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: New project...

Post: # 23263Post William »

Elton. What are the things that the ground hooks to? I can't figure out what they are? What you said makes sense as the feed from the amp would be a direct connection to the woofers and the caps would connect to the tweeters and midrange. Do you have a rating on the brown caps? I can see the 16uf, 25 volt on the other caps.

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23267Post hermitcrab »

William wrote: ↑Sat Oct 19, 2024 11:03 pm Elton. What are the things that the ground hooks to? I can't figure out what they are? What you said makes sense as the feed from the amp would be a direct connection to the woofers and the caps would connect to the tweeters and midrange. Do you have a rating on the brown caps? I can see the 16uf, 25 volt on the other caps.

Bill
Bill the two tied together inductors are the ground side , I did some searching on the web, and inductors are used a lot between the hot signal and ground the small ceramic caps are .01
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23268Post hermitcrab »

Here it is basically finished as far as the cabinet goes , this is the jumble of wires that I am trying to sort out and look neat... I will have to drill a couple holes to route the wires from the crossover to the speakers because at the moment they are too short to go around the dividers ...
Attachments
20241019_221347.jpg
20241019_221402.jpg
20241019_221433.jpg
User avatar
William
Global Moderator
Posts: 5515
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: New project...

Post: # 23269Post William »

Interesting, I did not know that, but I am not very knowledgeable about crossovers. Knowing what the value of the brown drop caps are, it then makes sense to me that the brown caps are for the horns and the 16uf are for the tweeters.

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23272Post hermitcrab »

Well I connected it all up, and crossed my fingers and flipped the switch... proud to say it plays beautifully and everything works great, the speakers seem to be doing their thing on the different frequencies so the crossover must be right ... the radio is very sensitive and so is the phono... you can hear the bad idler in-between tracks which I will have to order ... here is a quick video of it playing... and Freckles has to give his OK as well. https://youtu.be/FSfIQSVD7qI
User avatar
William
Global Moderator
Posts: 5515
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: New project...

Post: # 23274Post William »

Wow, that sounds great, Elton, even on cheap computer speakers. Where in the house is it going? I see your Magnavox 100 next to it, did the RCA Hutch take its place? Nice work, you should be proud.

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23277Post hermitcrab »

Bill, I told my wife I should make up a model name for it... like Barcelona , or Madrid.... she suggested the SOB.... apparently I was saying that a lot during the build... :lol:
Thanks
wparks
Full Member
Posts: 33
Joined: Thu Sep 26, 2024 8:49 pm
Location: Lewiston, Idaho
Contact:

Re: New project...

Post: # 23279Post wparks »

Wow, that looks really great hermitcrab- Great styling, and I really like the louvers- I know that is difficult to do. I have always loved the chocolate look of American Walnut- I really like the Watco Danish Oil products- it hardens in the wood making an easily repairable finish that does not require any top coating.

I was curious- What arrangement did you end up using on the crossover? I have studied two different Magnavox consoles, and what I find is that the woofers always get full signal, and the horns use a second order (one inductor, on capacitor) to roll off the low frequencies quickly so they don't "honk" with the lower frequencies. The 4 lugs with the inductors tied together would be for common distribution, the amplifier L and R would drive the white and red wires at the middle, with the woofer positives coming off those same lugs, then the horns would connect to the spades at the end of the large capacitors, the tweeters to the small capacitors. Just curious if that is how you did it.

I could not really hear a lot of bass in the recording on youtube (Thank you for posting a video, it sounds great), but it could be due either to song choice or to my crappy laptop speakers. How does the bass sound? Should be nice and powerful with those big speakers. Were you planning on putting a back on the cabinet to help contain the out of phase waves from the backside of the speakers, or probably just place it up against a wall?

I am really interested in the amplifier chassis that one uses- Did anyone find a free online schematic? I would love looking at that- It appears very similar to the Magnavox germanium amplifier that I am restoring right now (similar unit pictured). I did not see anywhere (maybe I missed it) - Did you have to do any work on the electronics? My Magnavox chassis had several plastic can electrolytics that had dried out (especially the smaller 5-50uF caps) and were really leaky.
Magnavox_A551_Germanium_Amplifier.jpg
Again, fantastic work, and thank you so much for taking us along with you on the journey.
wparks
Full Member
Posts: 33
Joined: Thu Sep 26, 2024 8:49 pm
Location: Lewiston, Idaho
Contact:

Re: New project...

Post: # 23280Post wparks »

Crap- i got that wrong.

The amplifier output would drive into the terminal that the large cap connects to, with common to the previously identified common where the inductors connect. The middle junction, where the white and red wires are shown, would go to the horn positive. The tweeters would still go to the spades with the smaller caps.

In this way the amp would drive the tweeter through only the small cap, the woofer directly, and the horn would be driven through the big cap in series, with the inductor going to ground as would be a typical second order filter. I can draw it out and post a picture if I am being confusing.
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23281Post hermitcrab »

wparks wrote: ↑Mon Oct 21, 2024 7:51 pm Wow, that looks really great hermitcrab- Great styling, and I really like the louvers- I know that is difficult to do. I have always loved the chocolate look of American Walnut- I really like the Watco Danish Oil products- it hardens in the wood making an easily repairable finish that does not require any top coating.

I was curious- What arrangement did you end up using on the crossover? I have studied two different Magnavox consoles, and what I find is that the woofers always get full signal, and the horns use a second order (one inductor, on capacitor) to roll off the low frequencies quickly so they don't "honk" with the lower frequencies. The 4 lugs with the inductors tied together would be for common distribution, the amplifier L and R would drive the white and red wires at the middle, with the woofer positives coming off those same lugs, then the horns would connect to the spades at the end of the large capacitors, the tweeters to the small capacitors. Just curious if that is how you did it.

I could not really hear a lot of bass in the recording on youtube (Thank you for posting a video, it sounds great), but it could be due either to song choice or to my crappy laptop speakers. How does the bass sound? Should be nice and powerful with those big speakers. Were you planning on putting a back on the cabinet to help contain the out of phase waves from the backside of the speakers, or probably just place it up against a wall?

I am really interested in the amplifier chassis that one uses- Did anyone find a free online schematic? I would love looking at that- It appears very similar to the Magnavox germanium amplifier that I am restoring right now (similar unit pictured). I did not see anywhere (maybe I missed it) - Did you have to do any work on the electronics? My Magnavox chassis had several plastic can electrolytics that had dried out (especially the smaller 5-50uF caps) and were really leaky.

Magnavox_A551_Germanium_Amplifier.jpg

Again, fantastic work, and thank you so much for taking us along with you on the journey.
Thanks , I had fun making it, this time I didn't make any huge mistakes so I called that a win .... I think I uploaded the sams for this ,should be labeled Montgomery ward I'll have to check that... as far as the crossover , I went the opposite way of wiring it... the inputs to the outer spades as are the woofers , the inner spades got the horns, and the tweeters are in the center , I was going to try the inputs to the center, but their are no extra spades to also connect woofers , so I figured my way was it. not that I am that sure
User avatar
TC Chris
Anchor Member
Posts: 3779
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: New project...

Post: # 23283Post TC Chris »

A great project, skillfully done. Nice beagle, too. And I'm jealous of all that space!

Chris Campbell
User avatar
William
Global Moderator
Posts: 5515
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: New project...

Post: # 23284Post William »

Hey, Elton, if it sounds good and you have not blown up the horns or tweeters it must be correct.

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: New project...

Post: # 23285Post hermitcrab »

I'm not sure if the horns are working, hardly any sound out of them, even plugging the amp directly into them, the 4" speakers are putting out more sound , these horns were made by Hoffman , but no specs on what their frequency response should be... for all I know the 4" speakers may be the midrange and the horns the tweeters, if that is true I will get new 4 inch speakers because the paper cones on mine are very tight... but going from 15" woofers down to a 4 " midrange would seem stupid... wouldn't it? :?
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests