A nice Packard
- TC Chris
- Anchor Member
- Posts: 3778
- Joined: Tue Jul 13, 2021 3:50 am
- Location: Traverse City, MI
- Contact:
A nice Packard
Our local film series has been showing "forgotten classics" and tonight we saw Steven Spielberg;s 1987 Empire of the Sun. I can send my appraisal of it by PM to anybody who is interested.
But knowing that we have some old-car fans here, I'll just say that it features a glorious Packard. I had guessed 1936 but a review says it was a "1938 Packard Super Eight with the 'cormorant' hood ornament." And it's RH drive, befitting the film's location, British Shanghai.
I pumped up a low tire on my '38 Buick on Sunday. I really need to find time to make it road-worthy, at least, if not pretty. I bought the car in 1966 so after 58 years you'd think something would have been accomplished.
Chris Campbell
But knowing that we have some old-car fans here, I'll just say that it features a glorious Packard. I had guessed 1936 but a review says it was a "1938 Packard Super Eight with the 'cormorant' hood ornament." And it's RH drive, befitting the film's location, British Shanghai.
I pumped up a low tire on my '38 Buick on Sunday. I really need to find time to make it road-worthy, at least, if not pretty. I bought the car in 1966 so after 58 years you'd think something would have been accomplished.
Chris Campbell
- William
- Global Moderator
- Posts: 5513
- Joined: Fri Jul 09, 2021 12:42 pm
- Location: Hart, Michigan
- Contact:
Re: A nice Packard
You just need to retire, Chris, so you have more time to enjoy all of your toys and projects that need to be done.
Bill
Bill
- electra225
- Site Admin
- Posts: 9074
- Joined: Thu Jul 08, 2021 7:48 pm
- Location: San Tan Valley, AZ
- Contact:
Re: A nice Packard
If you ask real nice, Chris, I might send you a diagram of my dual-voltage 12-volt conversion for your '38 Buick that you will probably need. You can hide two six-volt Optima batteries in the battery box of your car and, with the cover on, show judges can't tell you did it. Gives you hotter spark, brighter lights, and helps with hard cold starting after it sets and nearly always prevents vapor lock, a chronic problem with those old straight 8 Buicks. You can still use the six-volt radio, heater blowers and accessories because they are not powered thru the ignition switch. A potential issue you should investigate before you drive it too much is whether the water distribution tube in the engine block is still good enough to do its job. If it is rusted badly, you will experience chronic and mysterious overheating. Buick engineers put the temp gauge sender in the end of the cylinder head nearest the passenger compartment so if that tube rusted out, it would show a warmer temp so you wouldn't fry the engine. It is quite an extensive, potentially expensive job to renew the water distribution tube, particularly with the engine still in the car. The typical repair is to remove the engine, take it to the machine shop, disassemble the engine, then soak the remnants of the distribution tube and get it out that way. Sludge and rust in the engine block inhibit a successful replacement with the engine in the car.
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
- TC Chris
- Anchor Member
- Posts: 3778
- Joined: Tue Jul 13, 2021 3:50 am
- Location: Traverse City, MI
- Contact:
Re: A nice Packard
Now that is scary. I had assumed that mine was overheating because (1) the bypass thingy was in the glove compartment, and (2) my new rings were tight. But maybe the problem is worse....
Mine has no battery box, just a shelf and bracket, but I have the Allstate long skinny 6-V battery that I bought back in 1966 and maybe it would hide new cells?
Chris
Mine has no battery box, just a shelf and bracket, but I have the Allstate long skinny 6-V battery that I bought back in 1966 and maybe it would hide new cells?
Chris
- electra225
- Site Admin
- Posts: 9074
- Joined: Thu Jul 08, 2021 7:48 pm
- Location: San Tan Valley, AZ
- Contact:
Re: A nice Packard
Somebody has removed the battery box. That was commonly done since it made the battery hard to get in and out. If you aren't going to have the car judged by the Buick Club of America judging rules, then it will work fine like it is. Optima batteries have holes in their base that allows the batteries to be bolted to the car. I had to bolt them in when I did a Ford or a Hudson 12-volt, dual voltage, dual polarity electrical system conversion. I could run the lights, starter, "genernator" and ignition on 12 volts negative ground. The radio, heater blower and instruments ran on 6 volts positive ground. Fortunately for Buick, they ran on negative ground electrical systems so you didn't have to do the dual polarity conversion. Ignitors will run on positive ground, but they work better on negative ground. The most effective diagnosis of a potentially degraded water distribution tube is done with a digital pyrometer. You aim the device at the engine in several areas when it is fully warm or when it is overheating and if the temperature is more than 20 degrees different in the length of the engine block, then a blockage or insufficient coolant flow can reasonably be suspected. Almost any straight 8 engine will be warmer at the rear of the block, due to the length of travel for the coolant back to the radiator. The idea was for the water pump to deliver coolant to the rear of the block first, then let it move forward with circulation and heat toward the cooler radiator. Thermo-syphon was partially at work. The 6 cylinder Chrysler flatheads also had water distribution tubes, as did Hudson. BTW, for what it's worth, a "genernator" is a generator that has been converted to an alternator. A DC generator converted to an AC generator. This gives the stock appearance of the old Delco generator, but it works like an alternator. I used to use 60-amp genernators on Buick Straight 8's. I think the original generator was something like 30 amps. These dandy little devices allow you to use air conditioning on the older cars without having to hack the look of the engine compartment. The issue with a '38 Buick doing that is that the radiator is narrow, sets close to both the grille and the fan. Little to no room for a larger radiator and you have to stash the air conditioner condenser really low in front of the radiator. By the time you add an electric pusher fan in front of the condenser and install a six-blade engine cooling fan, clearance is extremely tight. You need at least an inch between the radiator core and the fan or you can suck the radiator into the fan. That may sound strange, but I have seen in numerous times. The most recent was with a '49 Buick that a guy took cross country and sucked the radiator into the fan in the middle of nowhere, Oklahoma.......

It is a poor practice to rebuild a Buick straight 8, or any straight 8 for that matter, in frame. I have seen sediment so thick and deep, essentially the entire lower end of the cylinder block is stopped up with sediment. The only water flow there was would have been above the distribution tube and head. The engine must be removed so the sediment can be removed completely. Nowadays, they would use a vat, a "hot tank" with caustic soda and water, heated, which soaks and removs the sediment without damage to the cast iron block. Grandpa used a water hose and compressed air he had rigged up. He would set the block on its end, the clean out the sediment that way. There is no way to remove the sediment with the engine in the car and not contaminate the rest of the internals with all that rust and sludge.
It is a poor practice to rebuild a Buick straight 8, or any straight 8 for that matter, in frame. I have seen sediment so thick and deep, essentially the entire lower end of the cylinder block is stopped up with sediment. The only water flow there was would have been above the distribution tube and head. The engine must be removed so the sediment can be removed completely. Nowadays, they would use a vat, a "hot tank" with caustic soda and water, heated, which soaks and removs the sediment without damage to the cast iron block. Grandpa used a water hose and compressed air he had rigged up. He would set the block on its end, the clean out the sediment that way. There is no way to remove the sediment with the engine in the car and not contaminate the rest of the internals with all that rust and sludge.
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
- TC Chris
- Anchor Member
- Posts: 3778
- Joined: Tue Jul 13, 2021 3:50 am
- Location: Traverse City, MI
- Contact:
Re: A nice Packard
So how many miles does to take to get all sludged up?
Chris Campbell
Chris Campbell
- electra225
- Site Admin
- Posts: 9074
- Joined: Thu Jul 08, 2021 7:48 pm
- Location: San Tan Valley, AZ
- Contact:
Re: A nice Packard
After nearly 90 years, you could suspect that all of them are full of sludge and rust if they haven't been vatted and rebuilt in the last 30 years or so. The old antifreeze breaks down and turns to goo. The proper maintenance on the cooling system back in the day included running water soluble oil in the cooling system to minimize rust. Then you drained and refilled the cooling system spring and fall. You would remove the "alkyhall" in the spring and run plain water for the summer, then drain again in the fall and add new "alkyhall" for the winter. Or you could pony up for "permanent" which didn't need to be drained except in the fall when you would do a drain, flush and refill. Even permanent antifreeze needed to be drained and flushed each fall because it would break down. You would also put in a "hot' thermostat in the fall so the heater would work well. And maybe add a piece of cardboard over the radiator to make the heater warmer.
I haven't failed. I've just found 10,000 ways that won't work.....Thomas Alva Edison
Who is online
Users browsing this forum: No registered users and 8 guests
