Magnavox R2R fix

Discussions about Magnavox consoles, tube and solid state, stereo and mono.
Post Reply
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Magnavox R2R fix

Post: # 2140Post hermitcrab »

this is the machine I mounted a small variac in the cabinet of the Imperial to keep the speed somewhat close ... only problem with that plan was the motor would stall in FF or REW under a 5 or 10 volt drop that it was running at...so since I had a day off , I tore it out and replaced the motor run cap... which is rated at .7uf ... when I measured the ESR is was reading just under 4 ohms!.... I did not have a .7 so I used one of my 1uf fan motor caps that measured .2 ohms... much better ... the new cap installed and the machine now plays at the correct speed without help of a variac ... didn't know a bad motor cap would speed up the motor... they usually slow down as the motor heats up... learn something new every day..
Attachments
20210929_182628.jpg
User avatar
William
Global Moderator
Posts: 5344
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: Magnavox R2R fix

Post: # 2141Post William »

Interesting story, Elton. I think I bring my R to R over and let you do your magic. As I have mentioned before, it's sick and I'm scared to tear into it. :oops:

Bill
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: Magnavox R2R fix

Post: # 2160Post hermitcrab »

Bill, these are all getting to the age where they need recapping. It doesn't matter what the brand is either , My Sony 366 just started acting up, one channel weak , but it has not been recapped yet other than the motor cap ... the Sony 250 that I totally recapped a year ago is now exhibiting static in one channel either one of the new caps was a dud or now it has a leaky transistor ... :cry:
User avatar
William
Global Moderator
Posts: 5344
Joined: Fri Jul 09, 2021 12:42 pm
Location: Hart, Michigan
Contact:

Re: Magnavox R2R fix

Post: # 2163Post William »

It's always something, Elton, but that is what makes it fun. Right? ;) :roll: :)

Bill
User avatar
TC Chris
Anchor Member
Posts: 3690
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: Magnavox R2R fix

Post: # 2169Post TC Chris »

How about some general advice on motor-run caps? I've got a couple 3-motor R to R machines with lazy takeup and rewind motors, and that aged caps may be the issue.

Sources, specs, etc?

Chris Campbell
User avatar
hermitcrab
Anchor Member
Posts: 1504
Joined: Mon Jul 12, 2021 2:49 am
Location: Tri Cities Mich
Contact:

Re: Magnavox R2R fix

Post: # 2170Post hermitcrab »

Just as every other application try to match the capacitance and voltage ratings of the cap you want to replace. Digikey and mouser are good sources , but shipping is crazy for a single cap. I usually buy ceiling fan caps from home improvement stores if they have the right capacitance in stock. Lazy motors are a sign of bad caps
User avatar
TC Chris
Anchor Member
Posts: 3690
Joined: Tue Jul 13, 2021 3:50 am
Location: Traverse City, MI
Contact:

Re: Magnavox R2R fix

Post: # 2175Post TC Chris »

I was wondering if motor-run caps have special characteristics. Somewhere I had read about using them for some other application that benefited from some characteristic that start caps had.

Chris Campbell
Post Reply

Who is online

Users browsing this forum: No registered users and 30 guests